Skip to the text
Arborist Certification Test

Independent study notes for arborists; not affiliated with ISA, TCIA or SAF.

Field index

Sources reread

Pruning to ANSI A300: cuts, systems and harmful practices

Domain 5 of 10 · 14% of the exam

After safe work, pruning is the weightiest domain. Its outline is less about naming cuts than about reasons: which objective a job serves, which cut fits a given union, how a tree's age and condition limit the work, and why some common practices are on ISA's list of harmful ones.

Answered 0 of 18 · 0 right

Question 1 of 18

Pruning cuts should be made just outside the branch collar because the collar:

Reveal the key without answering

The collar is built largely of trunk wood, and the chemical zone at the branch base slows decay from entering the trunk, so a cut that spares it leaves the trunk defended.

Treating the collar as spare branch tissue is the thinking behind flush cuts, which open the trunk itself.

Trees do not seal cuts with sugar or resin; they wall off decay inside and close the wound slowly with new wood.

Dressings do not stop decay and are not recommended for routine cuts, so they give no reason to cut at the collar.

Question 2 of 18

Lion-tailing a limb is harmful mainly because it:

Reveal the key without answering

Stripping the inner laterals leaves foliage only at the ends, so weight and wind act on the longest lever arm and the limb is more likely to fail.

Taking terminal buds is heading, which lion-tailing does not require; it leaves the branch ends intact.

Lion-tailing works along the limbs, not on the top of the crown; removing the top is a different practice.

Inner laterals can be removed with correct collar cuts and the limb is still lion-tailed; the harm is where the foliage ends up.

Question 3 of 18

Crown reduction differs from topping mainly because reduction:

Reveal the key without answering

Reduction ends each cut at a lateral big enough to become the new end of the stem, while topping leaves stubs or tiny laterals that cannot.

Reduction does lower height or spread; leaving the height alone describes thinning, not reduction.

The tool does not define either practice; both can be done with any saw.

Season does not separate them: a dormant-season job with stub cuts is still topping.

Question 4 of 18

A removal cut differs from a reduction cut in that a removal cut:

Reveal the key without answering

A removal cut takes a branch off at its point of attachment, just outside the branch bark ridge and collar, leaving the larger stem in place.

A flush cut is unacceptable: it takes the collar and makes a larger, deeper wound in the parent stem.

Shortening the larger stem to a smaller side branch defines a reduction cut, not a removal cut.

A cut between nodes is a heading cut, the type behind topping and shearing.

Question 5 of 18

Bypass hand pruners are preferred to anvil pruners for live twigs because bypass pruners:

Reveal the key without answering

The bypass blade slides past the hook like scissors, so it leaves a clean cut that can be placed right at the collar.

Neither type is meant for larger branches, which call for loppers or a saw.

No pruner is exempt; any blade can carry a pathogen from tree to tree when disease is present.

A stub protects nothing and the goal is a cut just outside the collar; stubs die back and decay.

Question 6 of 18

When restoring a topped tree, the sprouts chosen to become new limbs should be:

Reveal the key without answering

Restoration keeps the sprouts most likely to become sound limbs and gradually reduces or removes their competitors.

Repeated heading cuts just set off another round of sprouts.

Height alone keeps crowded sprouts that compete and form weak unions with one another.

Inward-growing sprouts crowd and rub the crown instead of rebuilding its outer framework.

Question 7 of 18

Young trees of decurrent species often need structural pruning mainly because they tend to form:

Reveal the key without answering

Decurrent species have weak apical control, so upright stems compete and form codominant unions, sometimes with included bark.

Branch collars form in decurrent species as in others; the issue is codominance, not missing collars.

Decurrent trees usually have plenty of branches; the issue is too many competing for the lead.

One strong leader is the excurrent habit, and it is the goal of structural pruning, not the problem.

Question 8 of 18

When subordinating a competing leader on a young tree, the arborist typically removes:

Reveal the key without answering

Subordination shortens the competing stem with a reduction cut, so the chosen leader outgrows it.

Pinching only the terminal bud is a heading cut that sets off strong new shoots right below it.

Stripping the inner laterals is lion-tailing and does not slow the stem's growth at its tip.

Taking the whole stem is a removal, not subordination, and a flush cut also takes the collar.

Question 9 of 18

When managing a veteran tree, retaining some dead wood in the crown can be justified because it:

Reveal the key without answering

Dead wood in veteran trees shelters insects, fungi, birds and bats, so where nothing is below it can be kept for its habitat value.

Compartmentalization is done by living cells; dead wood adds no defense.

Keeping dead wood cannot balance anything, since it has no leaves and draws no water.

Dead branches contribute nothing to wound closure; new wood comes from living tissue around the wound.

Question 10 of 18

A neglected, overgrown mature apple tree needs restoring. The arborist should:

Reveal the key without answering

Working in stages removes the overgrowth without taking away so much leaf area at once that the tree answers with a mass of water sprouts.

One hard cut is the shortcut that sets off a flush of water sprouts and starves the tree of leaf area.

Blanket heading cuts trigger dense vegetative shoots instead of fruiting spurs.

Topping produces upright sprouts, not fruiting wood, and leaves stubs that decay.

Question 11 of 18

Coppicing differs from pollarding in that coppiced stems are cut back:

Reveal the key without answering

Coppicing cuts stems back near the ground, and new shoots rise from the stool.

That shortens a stem; coppicing instead relies on repeated sprouting from the stool.

A collar cut removes a branch from a stem; coppicing removes the stem itself.

Cutting at a fixed height up the trunk is pollarding, not coppicing.

Question 12 of 18

Compared with dormant-season pruning, removing live branches in late summer usually:

Reveal the key without answering

Taking working leaves after the growth flush cuts the sugars the tree would have stored, so the response is weaker.

Maples bleed most in late winter and early spring, when sap pressure is high, not in late summer.

Removing leaves that are still making sugar lowers reserves; it cannot raise them.

Wounds close fastest when cuts are made just before or during the spring flush, not in late summer.

Question 13 of 18

Compared with young trees, mature trees generally:

Reveal the key without answering

Older trees have smaller reserves for their size and close wounds slowly, so each visit takes less live wood than on a young tree.

Heavy cuts to lighten a mature tree stress it and set off weakly attached sprouts.

Wound closure slows with age, so mature trees close large wounds more slowly, not faster.

Taking a share like that at once is what mature trees handle worst.

Question 14 of 18

Included bark weakens a branch union because:

Reveal the key without answering

Bark caught between the stems leaves part of the union with no connecting wood, so it can split.

A branch bark ridge does not girdle anything; included bark is a structural defect, not a decay or girdling one.

Included bark forms in narrow, tight unions; a wide angle usually means a stronger attachment.

Water flow is not the weakness; the problem is the missing wood across the union.

Question 15 of 18

In a crown cleaning specification, the arborist normally states:

Reveal the key without answering

A cleaning spec gives the smallest diameter of dead, dying or broken branches the crew must take, so the scope is clear to crew and client.

Cleaning targets dead and broken wood, so a live-crown percentage does not describe it.

Naming fungi is diagnosis, not a pruning instruction, and it does not tell the crew what to cut.

A branch count is impractical to set in advance and does not say which branches qualify.

Question 16 of 18

When maintaining an established pollard, the sprouts should be cut:

Reveal the key without answering

Sprouts are cut close to the swollen knuckle without wounding it, because the head holds the buds and defenses that produce the next crop.

Cutting into the head wounds the very tissue the system depends on and invites decay.

Cutting below the head goes into older wood the tree defends poorly and removes the bud-rich knuckle.

Stubs on each sprout die back and multiply the dead wood on the head.

Question 17 of 18

A client wants more sunlight on the lawn beneath a healthy shade tree. The BEST pruning approach is to:

Reveal the key without answering

Selective removal toward the branch ends lets light through while leaving foliage spread along the limbs.

Stripping the interior is lion-tailing, a harmful practice that weakens the limbs.

Topping creates stubs and a dense flush of sprouts that shades the lawn again within a few years.

Taking the lower half of the crown leaves too little live crown for the tree's needs.

Question 18 of 18

Pruning out dieback on a sycamore with anthracnose helps control the disease because the fungus:

Reveal the key without answering

The fungus survives the winter in cankers on infected shoots and releases spores in cool, wet springs, so removing them cuts the next season's inoculum.

Soilborne survival describes wilt pathogens such as Verticillium.

Anthracnose spores move by rain splash and wind, not beetles.

Spread through root grafts is typical of oak wilt and Dutch elm disease, not anthracnose.

–/18

Your tally on these questions

Only this browser tab keeps it; your picks go nowhere, and closing the tab wipes them.

Four tasks under Pruning

The outline frames pruning as a chain of decisions: an objective, a cut, a tool, and limits set by species, age and condition.

Pages 6 and 7 of the outline, task by task:

  • A · Objectives, systems and cut types: why a tree is pruned (structure, lower likelihood of failure, clearance, density reduction, restoration, size management), timing and amount by species and condition, how trees respond to wounds, and the standards behind the work: A300 with ISA's best management practices, and the British BS 3998.
  • B · Tools: scissor-type tools (hand pruners, loppers, shears, pole pruners), hand and pole saws, chain saws; choosing the tool for the cut, cleaning it and handling it.
  • C · Pruning with the least harm: branch unions (collar, branch bark ridge, codominant stems), CODIT, pruning systems, root pruning, utility pruning, the safety rules for pruning near conductors, disinfecting tools with alcohol-based solutions, writing objectives and specifications, and placing and sequencing cuts so bark does not tear past the union.
  • D · Harmful practices: topping, over-thinning, lion's-tailing and flush cutting, what they do to health and structure, and why some cuts and wound dressings can do damage.

One A300 since 2023, still cited by its old parts

The outline cites the "ANSI A300 Pruning Standard - Part 1", and the current text is ANSI A300 (2023) Tree Care Standards, one document that replaced the ten separate A300 parts. Introducing the consolidated standard in TCI Magazine, Bowman et al. (2023) make two points worth knowing. The standards are a framework for writing specifications fitted to a tree and a site, not ready-made work orders. And they do not apply to agriculture, horticultural production or silviculture.

The terms the outline uses for cuts (removal, reduction, heading and shearing cuts) and for objectives are the vocabulary of a specification. A written pruning job states the objective first, then the parts of the tree to work on, the types of cut, and the extent of the work.

Where the outline and the standard part ways

The 2022 outline names A300 parts (Part 1 for pruning, Part 6 for transplanting, Part 5 for construction), while the 2023 standard uses clauses with new numbers. The subject matter carried over; the numbering did not. Cite the standard by name, "ANSI A300 (2023)", rather than by part number.

Topping, and the honest alternatives

Topping is the practice of bringing a tree down to a chosen height with cuts made across stems to stubs or to buds, wherever the height line falls. The outline places it first among harmful practices. ISA's consumer brochure Why Topping Hurts Trees lists what it does:

  • Large cuts on old wood that the tree compartmentalizes poorly, so decay follows.
  • A sudden loss of leaf area, and with it the sugars that feed roots and defense.
  • Bark that was shaded, suddenly exposed to sun.
  • A thicket of fast sprouts at each cut, which needs repeated work and turns a single job into a cycle.

When a tree is too large for its place, the brochure points to reduction, or to removing the tree and replacing it with a species that fits. Explaining that choice to a client in plain words is one of the outline's listed skills.

Topping is not the same as pollarding, which the outline lists as a pruning system alongside espalier and pruning for fruit production.

Live crown ratio, utility work and root pruning

Live crown ratio

The Canadian Forest Service forestry glossary defines live crown ratio as the percentage of the stem's length that has living branches, a rough index of how well the crown can feed the rest of the tree. Raising, in ISA's Pruning Mature Trees brochure, removes lower branches to give clearance for buildings, vehicles, pedestrians and vistas, so every limb taken off the bottom lowers the ratio. A raising specification therefore states the clearance wanted, not just "raise the crown".

Utility pruning

Utility pruning is its own item in task C, and the same brochure names line clearance as a common reason for reduction. Pruning within reach of energized lines is also a safe-work subject, covered under safe work practices.

Root pruning

Root pruning is another task C item. At planting, the Installation and Establishment domain adds pruning roots and shaving root balls to prevent girdling and circling roots, and root severing by construction belongs to trees and construction.

Pruning terms that are easy to swap

  • A300 or Z133? A300 sets what is done to the tree. Z133 protects the people doing it. Where a cut goes is an A300 question; the climber's exposure while making it is a Z133 one.
  • Topping or pollarding? Both cut hard. A pollard is a system started young and kept on a cycle; topping is a height cut made wherever the line falls, on a tree never trained for it.
  • Crown cleaning or thinning? Cleaning removes dead, dying, diseased and broken branches. Thinning removes selected live branches.
  • Raising or reduction? Raising works from the bottom of the crown up, for clearance. Reduction shortens the height or spread from the outside in.
  • One rule for every tree. The outline ties the timing and amount of pruning to species, condition and environmental factors, so no single figure fits every tree.

Where pruning connects: tree biology for CODIT and why the location of a cut matters, tree risk for pruning as risk mitigation, and installation and establishment for structural pruning after planting.

For the ride to the next job

A300 and pruning: quick answers

What is ANSI A300?

The American consensus standard for tree care operations. Its subjects include pruning, soil management, lightning protection and tree risk assessment, among others, and it is written for people who care for or manage trees, shrubs and other woody landscape plants.

What else is topping called?

ISA's topping brochure lists heading, tipping, hat-racking and rounding over as other names for the same practice.

Should a pruning cut be painted or sealed?

As a rule, no. ISA's brochure Pruning Mature Trees says research has shown that wound dressings neither reduce decay nor speed wound closure, and the outline lists dressings among practices that can harm a tree.

Next domain

6 Diagnosis and Treatment

9% of the exam

Go to its questions
  • Safe Work Practices — 15% of the examZ133-2026, power lines, saws, lifts, PPE, felling basics
  • Tree Biology — 11% of the examAnatomy, water and sugar transport, CODIT, growth and decline
  • Tree Risk — 11% of the examRisk terms, targets, levels of assessment, mitigation, support systems

Documents behind this page’s facts

  1. OL

    ISA Certified Arborist Examination Outline, Job Task Analysis 2022 (PDF), pp. 1–15isa-arbor.com · read Nov 18, 2026

  2. PR22

    ISA news release of November 21, 2022 on the new Certified Arborist outline (Internet Archive copy, January 2023)web.archive.org · read Nov 18, 2026

  3. A300

    TCI Magazine (TCIA): the ten A300 parts combined into the ANSI A300 (2023) Tree Care Standardstcimag.tcia.org · read Nov 18, 2026

  4. 4

    Why Topping Hurts Treestreesaregood.org · read Nov 18, 2026

  5. 5

    Forestry glossarycfs.nrcan.gc.ca · read Nov 18, 2026

  6. 6

    Pruning Mature Treestreesaregood.org · read Nov 18, 2026