Skip to the text
Arborist Certification Test

Independent study notes for arborists; not affiliated with ISA, TCIA or SAF.

Field index

Sources reread

ANSI Z133 and safe work, in the tree and on the ground

Domain 9 of 10 · 15% of the exam

Safe Work Practices is the heaviest of the ten domains, and ISA's outline spreads it over ten tasks, from working to the safety standard to getting an injured climber down. This page maps those tasks onto the current edition of ANSI Z133, shows where federal OSHA rules sit beside it, and sorts out look-alike terms.

Answered 0 of 18 · 0 right

Question 1 of 18

A conductor has fallen to the ground near a worker, who feels tingling in the feet. The worker should move away by:

Reveal the key without answering

Voltage in the soil drops with distance from the contact point, so keeping both feet close and on the ground keeps them at nearly the same potential.

Hands and knees touch the ground at points farther apart, so crawling bridges more of the gradient.

Ordinary steps still separate the feet enough to let current flow; calm is right, but the stride is wrong.

A long stride spans a larger voltage difference between the feet, which is how step potential drives current through the legs.

Question 2 of 18

Earplugs and earmuffs worn together:

Reveal the key without answering

Plugs under muffs block more sound than one device, though far less than the two ratings suggest; OSHA's field estimate adds only about 5 dB to the better device.

A plug under a muff cannot lower what the muff already blocks; the pair is better, only not by much.

Double protection is a normal choice for very loud work such as stump grinding, provided signals can still be heard or seen.

Ratings do not add, because sound still reaches the inner ear through bone and around the seals.

Question 3 of 18

A climber feels faint while working aloft. What should the climber do FIRST?

Reveal the key without answering

Checking that the climber is secured to the tree first means a blackout ends with the climber hanging, not falling; the crew can then start a descent or rescue.

Faintness aloft is an emergency warning; carrying on, even slowly, leaves an impaired climber holding a saw.

Unclipping removes the only thing that would stop a fall if the climber passes out.

Hurrying down while dizzy is when control of the descent is most likely to be lost.

Question 4 of 18

A lowering line runs over a rigging block with both rope legs hanging parallel. The line holds a 600 lb (272 kg) piece. The load on the block is about:

Reveal the key without answering

With both legs hanging parallel, the block holds the piece on one leg and the lowering device's pull on the other, about twice the weight before any shock load.

Assuming the block sees only the piece's weight ignores the second leg, the error that leads to undersized rigging points.

Tripling the weight has no basis for a single redirect with parallel legs; dynamic loading is a separate, unpredictable addition.

Halving the load describes a mechanical advantage on a moving pulley, not the force on a fixed block in a lowering system.

Question 5 of 18

Which sign shows that a chain saw chain needs sharpening?

Reveal the key without answering

A dull chain scrapes rather than cuts, so it makes fine powder and has to be pushed into the wood.

Snapping back against the bar is a tension check, and it means the tension is right, not that the cutters are dull.

Large, coarse chips come from cutters that are still sharp and biting cleanly.

Feeding itself into the wood is what a sharp chain does; a dull one must be forced.

Question 6 of 18

Which location is BEST for a climber's tie-in point?

Reveal the key without answering

A live, solid union near the center and high enough over the work holds the climber's weight and keeps swings short.

Reach gained at the tip comes with a limb that can flex or fail under body weight.

Height alone is not the test; a thin top can bend or snap under a climber's weight and movement.

Dead wood can fail without warning however thick it looks, so it is never trusted as an anchor.

Question 7 of 18

Glazed, shiny, stiff spots on a rope's sheath are MOST likely caused by:

Reveal the key without answering

Heat from a fast descent or a hot device melts the surface fibers into shiny, stiff patches, and the rope is inspected closely and usually retired.

Ordinary aging makes a rope fuzzy and limp, not glossy and stiff.

A wet rope gets heavier and may stiffen when it freezes, but water does not melt the sheath.

UV fades and weakens fibers over time, but it does not melt them into a glaze.

Question 8 of 18

Which clothing hazard is MOST serious for a worker feeding a chipper?

Reveal the key without answering

Anything loose near the infeed can be hooked by a branch and drawn toward the feed wheels along with the brush, so chipper operators wear close-fitting gear.

Bare forearms get scratched, but skin gives the branches nothing to snag and pull.

Fabric choice affects comfort and heat stress, not entanglement at the infeed.

Color affects how visible a worker is in traffic, not whether the chipper can catch the clothing.

Question 9 of 18

When a stump grinder is started, the cutter wheel should be:

Reveal the key without answering

Starting with the cutter wheel lifted free of the stump and the soil keeps it from grabbing and jerking the machine or throwing debris the moment it spins up.

Soil contact at start-up throws rocks and dulls or breaks the teeth before any grinding begins.

Contact at start-up lets the spinning wheel climb or pull the machine sideways.

A wheel already in contact bites as soon as it turns, which can kick the grinder and fling chips.

Question 10 of 18

An aerial lift's boom hydraulics fail with the operator aloft. How should the bucket be brought down?

Reveal the key without answering

Aerial devices carry lower controls and an emergency lowering means for exactly this case, and ground workers are trained to use them.

Climbing the boom risks a fall and, near lines, contact with energized parts, and it leaves the bucket aloft.

A cut hose sprays fluid under high pressure and can drop the boom out of control.

Rappelling moves the worker, not the bucket, and is a last resort, not the way to bring the unit down.

Question 11 of 18

Before a ground worker enters the drop zone under a climber, the ground worker should:

Reveal the key without answering

The ground worker asks first and steps in only once the climber has answered that nothing will come down.

A one-way shout may not be heard aloft, and moving fast does not stop a piece from landing on the worker.

A quiet saw does not mean the climber knows someone is below; a piece can still be dropped or fall.

A pause may only mean the climber is setting up the next cut.

Question 12 of 18

Pesticides kept at a tree care company should be stored:

Reveal the key without answering

The original container carries the label with use, first-aid and storage directions, and a locked, ventilated area keeps out people who should not handle it.

Repackaging loses the full legal label, and poisonings often start with pesticide in an unexpected container.

The cab is where people sit and breathe, and it gets hot when parked, so it is the worst place for chemicals.

Storing pesticides next to PPE contaminates the very gear meant to protect the applicator.

Question 13 of 18

A barber chair is MOST likely when felling a tree that:

Reveal the key without answering

A strong forward lean loads the back of the trunk in tension, so a slow back cut can let the stem split upward before the hinge forms.

A back-leaning tree is hard to fell, but its risk is falling the wrong way, not splitting.

A small, straight-grained stem carries little stored tension, so it is the least prone to split.

The notch type is not what sets up a split; an open face is a standard felling notch.

Question 14 of 18

During felling, what happens if the back cut severs the hinge?

Reveal the key without answering

The hinge steers the tree as it falls, so once it is cut through the tree can fall, twist or slide in any direction.

An early-closing notch comes from a notch cut too small, not from severing the hinge.

Without a hinge the notch no longer guides the fall, so the tree does not reliably go that way at all.

A split like that starts before the hinge is cut, during a slow back cut, not after the hinge is gone.

Question 15 of 18

A ground worker is bitten by a venomous snake. The crew should:

Reveal the key without answering

Keeping the victim still slows the spread of venom, and antivenom is given only in a hospital, so reaching care quickly matters most.

A tight band traps venom in the limb and concentrates the damage, which can cost the limb.

Ice adds cold injury to tissue already damaged by venom and does not stop it.

Cutting and suction remove little venom and add infection and tissue damage.

Question 16 of 18

As a branch being fed into a chipper is grabbed by the feed wheels, the operator should:

Reveal the key without answering

Releasing the branch once the feed wheels take it and stepping out of line with the infeed keeps hands away and keeps the whipping butt from hitting the operator.

The feed wheels are far stronger than a person, and holding on lets the branch pull the operator along with it.

Following the branch brings hands and arms right up to the infeed.

Pushing until the end disappears is how hands end up at the feed wheels.

Question 17 of 18

A speedline is used in tree removal to:

Reveal the key without answering

A speedline is tensioned from the tree to an open landing spot, so pieces slide along it away from targets below the crown.

Rigging lines are never used to move people; climbers are carried only on life-support equipment.

Lowering beside the trunk is ordinary rigging with a lowering line and friction device.

A pull line helps direct a fall; it is not a line pieces travel along.

Question 18 of 18

A wire-core flipline is NOT suitable for:

Reveal the key without answering

The steel core that resists saw cuts also conducts electricity, so a wire-core lanyard is kept away from power lines.

Wrapping a large trunk for positioning is the ordinary use of any flipline.

Removals with a saw are the job the wire core exists for.

Spurs and a cut-resistant flipline are the normal pairing on a removal.

–/18

Your tally on these questions

Only this browser tab keeps it; your picks go nowhere, and closing the tab wipes them.

Ten tasks behind the largest domain

ISA publishes weights for domains only, so nobody outside ISA can say how many items deal with power lines, climbing or felling on their own.

The tasks as the outline lists them (pages 11 to 13), put in our own words:

  • A · Standards and law: working to ANSI Z133 and to local rules at every level of government, fire safety with gas-powered and electric tools, and keeping the work zone secure. The outline also cites the British BS 3998 and ISO 11681-2, the safety standard for chain saws built for tree service.
  • B · Planning the job: reading the tree and the ground around it before anyone climbs, the job briefing, traffic control, securing fuel and chemicals when not in use, ergonomics, stinging and biting animals and toxic plants, and the command-and-response calls between the tree and the ground.
  • C · Electrical hazards: telling transmission from primary and secondary distribution lines, bare from covered conductors, direct from indirect contact, and keeping minimum approach distances.
  • D · Tools and machines: hand tools, pruning saws, chain saws, chippers, stump grinders, aerial lifts (mobile elevating work platforms, MEWPs) and cranes, each checked before use and run as its maker specifies.
  • E · Protective equipment: head, eye, hearing, leg, foot and hand protection, and the climbing gear itself: saddle, connecting links, lanyards, friction devices and spurs.
  • F · Climbing: rope systems, knots and rope tools, tying in, and a controlled ascent, descent and stay aloft.
  • G · Rigging: lowering devices, blocks and pulleys, tag lines, butt and tip ties, and whether the tree can hold the anchor point under load.
  • H · Felling and dismantling: a felling plan with an escape route, the cuts that steer a tree, taking a tree down in pieces from aloft, and the hazards of a removal.
  • I · Emergencies: the emergency action plan, first aid, CPR and aerial rescue, then reporting what happened.
  • J · Safety culture: training, and making the case for it to coworkers and managers.

Z133-2026, OSHA and the rest of the rulebook

The outline names "ANSI Z133 Safety Requirements for Arboricultural Operations" with no edition year. The edition in force is ANSI Z133-2026, the US safety standard for tree work, available since May 27, 2026; it replaced the 2017 edition. Material written before mid-2026 can only quote the 2017 text. Where such a source gives a distance, a load or a clearance, check it against the 2026 edition before you learn it. This page states principles and leaves the tables to the standard.

Z133 is a voluntary consensus standard. Federal regulations apply beside it in particular situations. 29 CFR 1910.269 covers electric power generation, transmission and distribution, and its paragraph (r) adds requirements for line-clearance tree trimming. 29 CFR 1910.67 governs vehicle-mounted elevating and rotating work platforms, the bucket trucks of tree work, and says that only trained persons may operate an aerial lift. Task A asks for the habit behind all of this: knowing which rules reach a given job, and keeping the reference material at hand.

Overhead conductors: read the line before the tree

Task C begins with recognition. Transmission lines carry power between generating plants and substations on tall structures; primary distribution lines feed a neighborhood from the substation; secondary lines run from a transformer to the building at the lowest voltage. A covering is not insulation a worker can rely on: OSHA defines a covered conductor as one whose covering has no rated insulating strength, or a rating below the voltage of its circuit, in 29 CFR 1910.269(x).

Contact can be direct, when a body part touches an energized conductor, or indirect, when the worker touches something that does: a limb, a pole pruner, a rope, a truck. The minimum approach distance is the closest a worker, and any conductive tool the worker holds, may come to an energized part; it grows with voltage. The distances themselves are set in Z133-2026; the numbers stay with the standard.

Clearing trees for a utility is a specialty of its own, with its own OSHA paragraph and its own ISA credential, the Certified Arborist Utility Specialist.

Saws, chippers, grinders and buckets

For every machine the outline asks the same three things: inspect it before use, recognize operational flaws, and use it the way its manufacturer specifies.

Chain saws and kickback

Kickback appears twice in task H, both times under work positioning, while the saw's own safety features are a separate item. The saw's features (chain brake, chain catcher, reduced-kickback chain) limit what happens when the upper part of the bar nose catches wood and the bar is thrown back toward the operator. Positioning keeps the operator's body out of the line the bar would travel. ISO 11681-2, cited in tasks A, D and in Pruning, covers chain saws built for tree service.

Chippers and stump grinders

One machine pulls material in under power, the other throws chips at speed. The outline lists them together as one item in task D.

Aerial lifts

The outline calls them mobile elevating work platforms. Operating one is a matter of the employer's training under 29 CFR 1910.67.

  • ISA's lift credential: The ISA Certified Tree Worker Aerial Lift Specialist® is a separate credential with classroom and field tests; it needs 18 months in arboriculture, 6 of them operating an aerial lift.

Protective gear the outline names

Task E is a checklist with a skill attached: choose the right item, inspect it, wear and adjust it, and look after it.

  • Head: climbing helmets and hard hats.
  • Eyes and face: safety glasses, goggles, face shields.
  • Hearing: earplugs and earmuffs.
  • Legs: saw-protective chaps or trousers.
  • Feet: work boots with ankle support.
  • Hands: cut-resistant, flame-resistant and anti-vibration gloves, each for a different exposure.
  • Climbing equipment: saddle, connecting links, work-positioning lanyard, friction management devices, spurs. The outline asks that it meet the regulations and the industry standards for tree climbing.

Climbing, rigging and felling in outline

Climbing (F) and rigging (G) appear in the task list above in the outline's own terms. Task H, felling and dismantling, is the most detailed of the three: a felling plan weighs lean, wind, the tree's natural direction of fall, terrain, structures and targets, then fixes a drop zone and an escape route. The outline names the cuts (directional notch, spear cut, drop cut, snap cut), the tools that add control (tag line, rigging rope with mechanical advantage, felling wedges) and the hazards: barber chair, loss of directional control, lean, wind, power lines.

Emergencies, wildlife and the crew

Task I pairs four knowledge items (an emergency action plan, first aid, CPR, aerial rescue) with four skills: assessing environmental hazards, securing the scene, communicating with emergency responders, and documenting and reporting to stakeholders afterward.

Task B lists the living hazards by name: arboreal mammals, bees, ticks and Lyme disease, mosquitoes and dengue fever, snakes and other reptiles, poison ivy and poison oak. Task J closes the domain with training, on the outline's reasoning that it prevents injuries, prepares a crew for emergencies and protects productivity.

Safe-work pairs that get swapped

  • A standard or a regulation? Z133 is a consensus standard; 29 CFR 1910.269 and 1910.67 are federal regulations. Both can apply to the same job.
  • Direct or indirect contact? Indirect contact needs no touch of the wire at all, only of something that is touching it.
  • Felling or dismantling? Felling drops the whole tree from the ground. Dismantling takes it apart from aloft, piece by piece, by free fall, by cut and fall, or by rigging.

Related topics on this site: tree risk for judging a tree before anyone climbs it, pruning for the cuts made once aloft, and trees and construction for protecting roots and soil around the work.

On your phone, between jobs

Z133 and crew safety: short answers

Which edition of ANSI Z133 is current?

The current edition is Z133-2026. The exam outline cites Z133 without a year, and notes written before mid-2026 quote the 2017 text, so check any distance or number you memorize against the new text.

Is ISA certification an aerial lift certification?

No. It certifies arboriculture knowledge in general, not the operation of any particular lift; that training comes under the OSHA rule for vehicle-mounted lifts. ISA's lift credential is a separate one, described in the equipment section.

Does the exam test climbing skill?

No. Climbing, rigging and felling are tested as knowledge, not as a climb: the exam is multiple choice throughout (four answer choices per question, with one correct).

Next domain

10 Urban Forestry

6% of the exam

Go to its questions
  • Pruning — 14% of the examA300 (2023), cut types, pruning systems, topping and lion's-tailing
  • Tree Biology — 11% of the examAnatomy, water and sugar transport, CODIT, growth and decline

Documents behind this page’s facts

  1. OL

    ISA Certified Arborist Examination Outline, Job Task Analysis 2022 (PDF), pp. 1–15isa-arbor.com · read Nov 18, 2026

  2. PR22

    ISA news release of November 21, 2022 on the new Certified Arborist outline (Internet Archive copy, January 2023)web.archive.org · read Nov 18, 2026

  3. 3

    29 CFR 1910.269osha.gov · read Nov 18, 2026

  4. 4

    29 CFR 1910.67osha.gov · read Nov 18, 2026

  5. PG

    ISA Certified Arborist Program Guide, revised August 2025 (PDF), pp. 3–8isa-arbor.com · read Nov 18, 2026

  6. Z133

    ISA: Z133-2026 safety standard, approved by ANSI, available from May 27, 2026isa-arbor.com · read Nov 18, 2026

  7. AL

    isa-arbor.com credential page: ISA Certified Tree Worker Aerial Lift Specialistisa-arbor.com · read Nov 18, 2026