Many trees that die young had the root flare buried, left in their wire basket or wrapped in their own roots before anyone noticed. This domain covers putting a tree in the ground to accepted standards and keeping it alive until its roots have grown out into the site.
Answered 0 of 17 · 0 right
Question 1 of 17
A soil berm (water ring) for a newly planted tree should be built:
Reveal the key without answering
Nearly all of a new tree's roots are still inside the root ball, so the ring is built at its edge to hold water over them, then left to flatten as roots grow out.
A ring that far out holds water over soil the roots have not reached, while the ball itself can stay dry.
The mature dripline may be many feet beyond any roots for years; water held there is wasted on a new tree.
Water pooled against the trunk keeps the flare wet and invites decay while missing much of the ball.
Question 2 of 17
Which site factor MOST limits the eventual size and life span of a street tree in a paved area?
Reveal the key without answering
A crown can grow only as large as its roots can support, and paved sites usually give roots very little uncompacted soil, which caps size and shortens life.
The grate is only the surface opening; what limits the tree is the soil beneath it.
Reflected heat adds stress and affects species choice, but a tree with ample rooting space copes with it far better than one without.
Planting size does not predict how big or old a tree becomes; larger stock often establishes more slowly.
Question 3 of 17
ISA recommends that a planting hole be dug:
Reveal the key without answering
A wide, shallow hole puts loosened soil where new roots spread, while the undisturbed base under the ball keeps the tree from sinking.
A hole barely wider than the ball leaves new roots facing compacted native soil almost at once.
This hole is both too narrow and too deep: no loosened soil for roots to spread into, and settling backfill under the ball.
Loose soil placed under the ball settles after watering, and the tree sinks below its planting depth.
Question 4 of 17
A newly planted tree is considered established when:
Reveal the key without answering
Establishment means the root system has regrown enough to support the crown, and the visible signal is shoot growth back at the rate normal for that species.
The first flush after planting is powered by reserves built up in the nursery, so a full leaf-out in the first spring says nothing yet about root regrowth.
Flowering and fruiting often run on stored reserves and say little about whether the roots have recovered.
Roots reaching the edge of the old hole are only partway; they still have to spread well into native soil before they can support the crown.
Question 5 of 17
For a balled-and-burlapped shade tree, the minimum root-ball diameter is set by the tree's:
Reveal the key without answering
For shade trees the nursery stock standard (ANSI Z60.1) ties the minimum ball diameter to trunk caliper, so a thicker trunk gets a larger ball and keeps enough roots for its crown.
Mature size matters when choosing a species for the site; it does not set how much root ball is dug.
Crown width depends on pruning and spacing in the nursery and is not what the standard uses to size the ball.
Height is used to grade some small and coniferous stock, but for a shade tree the ball size follows the trunk.
Question 6 of 17
When planting a tree on a steep slope, the arborist should:
Reveal the key without answering
A small level bench lets irrigation and rain soak into the ball instead of running off, with a low ridge of soil on its downhill edge to hold the water; the trunk itself stays plumb.
Burying the uphill side to cover roots sets that side of the tree too deep.
Trees grow vertically on slopes too; a trunk set at right angles to the slope leans and has to correct itself as it grows.
Soil piled against the trunk keeps bark wet and sheds water away from the root ball rather than catching it.
Question 7 of 17
Where deer browsing is heavy, the MOST reliable protection for young trees is:
Reveal the key without answering
A physical barrier high enough to keep deer off the leader and crown is the one method that holds up under heavy browsing pressure.
Repellents wear off with rain and new growth, so a single spray at planting gives little lasting protection.
"Deer resistant" means less preferred; when deer are numerous and food is short, they browse those species too.
A short guard covers the lower trunk and leaves the leader and crown, where deer feed, fully exposed.
Question 8 of 17
Voles and rabbits are MOST likely to injure young trees by:
Reveal the key without answering
Voles under snow or mulch and rabbits above it gnaw bark and cambium near the ground in winter, and a full ring of chewing can kill a young tree.
Neither animal mainly strips leaves; their worst damage comes in winter, when the trees are leafless.
Digging for grubs is the work of skunks and raccoons, which disturb sod and mulch but seldom kill trees.
Browsing of the leader and upper shoots is typical of deer, well above the height where voles feed.
Question 9 of 17
When spacing trees in a new planting, the MOST important factor is each species':
Reveal the key without answering
Spacing is planned for the size trees will reach, so each species' mature crown spread sets the distance and avoids crowding and later removals.
Root ball size describes the tree on planting day and says nothing about the room it will need later.
Height at planting is temporary; trees spaced for their planting size crowd each other within a few years.
Growth rate decides how soon crowns meet, not how far apart trees need to be once they are full-sized.
Question 10 of 17
A planting hole with sloped, saucer-shaped sides is preferred because it:
Reveal the key without answering
A steep, smooth-sided wall, especially one glazed by a spade or auger in clay, acts like a pot wall and turns roots sideways; a sloped, roughened wall lets them cross into native soil.
Most tree roots grow outward in the upper soil rather than straight down, so anchorage is not the reason the sides are sloped.
Water collecting under the ball saturates the roots rather than helping them; hole shape is about root spread, not water storage.
The ball rests on undisturbed soil at the correct height whatever the wall shape; sitting lower would set the tree too deep.
Question 11 of 17
For a compacted urban site that cannot be remediated, which species trait matters MOST?
Reveal the key without answering
Compaction crushes the large pores that hold air, so roots in such soil face low oxygen and slow drainage; species adapted to periodically wet sites cope best.
Taproots cannot push through compacted layers, and most landscape trees do not keep a dominant taproot anyway.
Fast growth raises the tree's demand for water, which roots in dense, poorly aerated soil struggle to meet.
A large-maturing species copes no better with dense, poorly aerated soil; size does nothing for roots short of oxygen.
Question 12 of 17
Which tree is commonly listed as a poor fall transplanter, better moved in spring?
Reveal the key without answering
Oaks with coarse, sparse roots, such as northern red oak, regrow roots slowly and appear on most fall-planting hazard lists, so spring planting is usually advised.
Norway maple regrows roots readily and moves well in fall; its drawbacks, such as invasiveness, have nothing to do with planting season.
Littleleaf linden has a dense, fibrous root system and is one of the easier trees to transplant in either season.
Green ash is among the easiest trees to transplant, fall or spring; its problem today is emerald ash borer, not root regrowth.
Question 13 of 17
During the first year, ties on a staked tree should be:
Reveal the key without answering
As the trunk thickens and ties shift, a tie can rub or cut into bark within one season, so ties are checked through the year and loosened or moved.
Unchecked ties are how staking injury happens: by the time the stakes come out, a tight tie may have girdled the trunk.
Tightening holds the trunk rigid, which reduces trunk taper and makes the tie more likely to bind as the trunk grows.
Bare wire cuts into bark and cambium; ties should be broad, flexible material.
Question 14 of 17
Winter sunscald on a young thin-barked tree usually appears on the trunk side facing:
Reveal the key without answering
On sunny winter afternoons the south-to-southwest side of the trunk warms enough to deharden the cambium, which is then killed when temperatures drop after sunset.
The shaded north side stays cold and dormant all day, which is exactly why it escapes the warm-then-freeze cycle.
Winter wind dries out twigs and evergreen foliage; it does not warm bark, so it does not cause sunscald.
The east side gets sun while the air is still cold and the bark warms less, so injury there is less common.
Question 15 of 17
Compared with a cold climate, a tree of the same size usually establishes in a warm climate:
Reveal the key without answering
Establishment depends on regrowing lost roots, and in mild climates roots grow nearly year-round; University of Florida guidance gives about 3 to 4 months per inch of trunk diameter in zones 8 to 11 versus about 12 in zones 2 to 5.
Trunk size sets how much root system must be rebuilt, but climate sets how fast that happens, so the rate is not the same.
Heat raises water demand, but with irrigation, roots in warm soil regrow quickly rather than slowly.
Trees do not need a cold rest to grow roots; a longer warm season gives more root-growing time, not less.
Question 16 of 17
Root stimulant products applied at planting:
Reveal the key without answering
Trials of root hormones, vitamin B1 and biostimulant products at planting have given mixed or no benefit; correct depth, root quality and water matter far more.
No product has a consistent record of doubling root growth; claims like this come from marketing, not from trials.
No planting standard requires a root stimulant for any stock type; it is an optional product, not a specification.
No additive replaces water; a new tree depends on regular irrigation until it is established.
Question 17 of 17
A new tree in clay soil is watered daily and its leaves are yellowing and wilting. The MOST likely cause is:
Reveal the key without answering
Daily water in clay keeps the pores full, roots suffocate and stop taking up water, and the leaves wilt and yellow as if the tree were dry; a probe shows a wet ball.
With daily irrigation in a slow-draining soil, drought is unlikely; adding more water would deepen the real problem.
Yellowing with wilting on a constantly wet site points to failing roots; fertilizer cannot help roots that lack oxygen.
Calling it normal shock and doing nothing lets the roots keep dying in waterlogged soil.
–/17
Your tally on these questions
Only this browser tab keeps it; your picks go nowhere, and closing the tab wipes them.
Planting in the 2022 outline
The 2022 outline nearly doubled this domain's share of the exam, which had been 5%. ISA divides Installation and Establishment into two tasks: planting and transplanting to accepted standards (Task A), and caring for newly planted trees so they survive and grow good structure (Task B).
The neighbors share the root zone, so each keeps its own part. Soil volume, mulch and drainage are on soil management. Choosing the species for the site is on tree identification and selection. The first structural cuts on a young tree are on pruning, and guying or bracing a mature tree falls under tree risk.
Tasks A and B in plain words
What the outline asks for under Tasks A and B:
Standards: the outline still names the former A300 Part 6 transplanting standard, now part of the single ANSI A300 (2023) document, along with ISA's Tree Planting BMP, ANSI Z60.1 for nursery stock, and British and Canadian standards.
Nursery stock: how trees are propagated and grown, and what each stock type gains and gives up.
Timing and placement: season, stock type, water, temperature, sunlight, and where the tree goes on the site.
Inspection: judging the trunk, crown and roots of planting stock before it is bought.
The hole and the roots: preparing the site, correcting circling roots, and taking off wire, burlap, twine, crates and pots.
Backfill: amendments, settling, and how the root ball interacts with the soil around it.
Transplanting: moving an existing tree, from transport and site choice to care afterward.
Aftercare: water, mulch, support, trunk wrap, young-tree pruning, a plant health care plan, and getting residents and volunteers to look after new trees.
Bare root: sold with no soil ball. NDSU calls it the least costly type and the lightest to transport, planted only while dormant, with the roots kept moist in packing material until planting. CSU Extension's Tree Planting Steps (2024) spreads the roots over a mound of soil and notes that many bare-root trees need staking.
Balled and burlapped (B&B): dug from a field with a ball of soil, then wrapped in burlap and twine and often set in a wire basket. NDSU notes the heavy ball makes it harder to move and that the tree loses the vast majority of its roots at harvest, so it suffers more transplant shock.
Container-grown: grown in a pot for more than one season, so the root system is intact; NDSU lists it as the most common stock type and plantable from spring to early fall. It is also more prone to stem-girdling roots: roots that hit the pot wall turn and circle, and a tree left too long in its container can arrive with a dense mat of them.
Tree spade: NDSU's fifth stock type, a larger tree dug and moved by machine with its soil in one piece.
Root flare, circling roots and girdling roots
The root flare (or root collar) is where the trunk widens into the main structural roots. On nursery stock it is often buried under extra soil in the ball or the pot. CSU's guide describes probing the ball near the trunk with a slender tool to find the first structural roots, and warns against mistaking the swollen graft union for the flare.
Circling roots run around the inside of a container. Before planting, CSU shaves off the outer 1 to 1½ inches of the root ball to cut through them; left alone, NDSU warns, they may eventually compress the stem as girdling roots.
Root collar excavation removes soil from the base of an established tree to look for a buried flare and girdling roots. In an NC State Extension plant health alert (2024), it is the first check an agent makes on a sick maple.
Wire baskets, burlap and backfill
CSU leaves the burlap, wire and twine on a B&B ball until the tree stands in its final position, because they hold the ball together while it is moved. After that, the wrapping comes off: CSU calls leaving burlap, twine and wire on the sides of the ball unacceptable. The guides differ on how far down to cut. CSU removes the wrapping from the upper 12 inches or the upper two-thirds of the ball, whichever is greater, while Purdue Extension's FNR-FAQ-18 removes the top third of the basket.
For backfill, CSU returns the soil that came out of the hole and lets water settle it. A small share of organic matter in the backfill is acceptable in that guide, but backfill amended to 25 to 50 percent organic matter can hold too much water and discourage roots from leaving the hole. Backfill does not go on top of the root ball.
The first seasons after planting
Task B is about the years between planting and establishment.
Water is the main aftercare job. How often depends on the stock, the soil and the weather, and it is judged by checking moisture in the root ball itself.
Mulch covers the backfill and beyond; how deep, what kind, and why it never touches the trunk are on soil management.
Support is the exception, not the rule. CSU finds staking unnecessary in most landscape settings when the tree sits on undisturbed soil with a firmed ring of soil at its base, and describes underground stabilization of the ball as an alternative to stakes above ground.
Young-tree pruning sets up a single leader and well-spaced scaffold branches; the cuts are on pruning.
People: the outline adds engaging local communities, residents, students and nonprofits, since many street and park trees depend on them for care after the planting day.
Planting errors to unlearn
Graft union for root flare. The bulge of a graft sits higher on the stem; planting to it buries the real flare.
Circling and girdling roots as one thing. Circling roots are a container defect you can cut at planting; a girdling root is the later result, pressing on the trunk.
Leaving the basket on the sides because it holds the ball. It holds the ball only while the tree is moved.
Rich backfill to help the tree. Heavily amended backfill can keep roots inside the hole.
Staking every tree by default. Support is added only when the site or the stock calls for it, and the trunk is left free to move.
Mulch piled against the trunk. One line here; the rest is on soil management.
It is the base of the trunk where it widens into the main structural roots, also called the root collar. Nursery trees often have it buried under extra soil in the ball or pot, so planters find it by probing or removing that soil before setting the depth.
Is a potted tree the same as a container-grown tree?
No. In NDSU's terms, a potted tree is a bare-root tree planted in a container and grown there for less than one season, so its root system may be poorly developed and the root ball may fall apart when it comes out of the pot. A container-grown tree has been in its container for more than one growing season.
What are girdling roots?
Roots that grow across the trunk or a main root and press into it as both thicken, restricting the tree's own transport. CSU Extension links trunk-girdling roots to trees planted too deep, in the container or in the ground, and notes they can kill a tree twelve to twenty years after planting.